
A confirmation test begins a minute too early. A printer fails. A technician forgets to sign the Alcohol Testing Form. Each situation creates a problem, but DOT regulations do not treat all problems the same way.
For breath alcohol technicians (BATs), knowing the difference protects the employee’s right to an accurate test and helps employers maintain compliant testing programs. It also prevents unnecessary cancellations when a documentation error can still be corrected.
DOT alcohol testing mistakes fall into three important categories: fatal flaws that invalidate a test, correctable flaws that require cancellation if unresolved, and other procedural errors that do not automatically cancel a test. Understanding these distinctions is essential to applying 49 CFR Part 40 correctly.
What Are Fatal Flaws in DOT Alcohol Testing?
Fatal flaws are specific problems identified in Part 40 §40.267 that require cancellation of the affected alcohol test. A written explanation cannot make the flawed result valid. When practicable, the technician should promptly repeat the testing process under the applicable DOT procedures.
For BATs researching “fatal flaws alcohol testing,” the following table summarizes the breath-testing problems that trigger cancellation:
| Testing Problem | When the fatal flaw applies |
| Displayed and printed test result doesn’t match | Screening or confirmation on an evidential breath testing device (EBT), when the sequential test number or alcohol concentration differs |
| Confirmation test begins before 15-min wait ends | Confirmation testing |
| Required Air Blank is omitted | Confirmation testing |
| Required -pre-confirmation Air Blank result is not 0.00 | Confirmation testing |
| EBT fails to print the test result | Confirmation testing |
| Next external calibration check (accuracy check) is outside the QAPs acceptable tolerance range | Results of 0.02 or higher obtained since the last valid external calibration check are cancelled |
These cancellation conditions can be found in 40.267 of the federal regulations.
Mistake 1: Rushing the Confirmation Waiting Period
After a screening result of 0.02 or higher, confirmation testing is required. The waiting period must last at least 15 minutes, measured from completion of the screening test.
For example, if screening finishes at 10:00 a.m., starting confirmation at 10:14 a.m. is too early. A busy waiting room or an employer’s request to move faster does not shorten the requirement.
Explain that the employee must not eat, drink, put anything in the mouth, or belch during the waiting period. Explain why these instructions matter: mouth alcohol can artificially increase a reading.
If the employee disregards the instructions, document the behavior in the ATF Remarks. DOT directs you to conduct confirmation at the end of the waiting period even if the instructions were not followed.
A practical safeguard is to record the screening completion time immediately and calculate the earliest confirmation time before proceeding. Avoid relying on memory while answering calls or preparing another employee’s paperwork. A more practical safeguard is to set a 15-minute timer upon giving the employee the wait instructions.
Mistake 2: Skipping the Air Blank or Ignoring Its Reading
Before confirmation, conduct the air blank in the employee’s presence and show the reading. If it exceeds 0.00, perform a second air blank. If the second also exceeds 0.00, remove the EBT from service and use another EBT if available.
The instrument cannot return to testing until an external calibration check establishes that it is within the allowable tolerance range as indicated in the device’s quality assurance plan (QAP).
Do not confuse an air blank with an accuracy check. An air blank assesses whether alcohol is present in the device’s air sample; an external accuracy check evaluates instrument performance against a known alcohol standard.
Make the air blank an explicit checkpoint in your confirmation workflow. Familiarity with an instrument should reinforce the sequence, especially when a screening result creates pressure to act quickly.
Mistake 3: Missing a Display and Printout Mismatch
Compare the sequential test number and alcohol concentration shown on the instrument with the printed information. A mismatch during screening or confirmation on an EBT is a fatal flaw that will cancel the test.
This comparison deserves deliberate attention in busy clinics and mobile operations. Several printouts on a work surface can create confusion. To mitigate this mistake, immediately attach printed test results to the Alcohol Test Form (ATF) and review each printed result before moving to the next test.
Mistake 4: Accepting a Confirmation Result Without a Printout
The EBT must print the confirmation result. A handwritten transcription or photograph of the display does not replace that requirement.
Show the employee the printed result and unique test number. When the EBT produces a separate printout, attach it to the ATF using tamper-evident tape or a tamper-evident self-adhesive label.
Before testing begins, check printer readiness, paper, connections, and power. Include these checks when setting up away from your usual testing location.
Mistake 5: Treating Accuracy Checks as Optional
An EBT’s QAP establishes accuracy-check methods, acceptable tolerances, and required intervals. Follow the manufacturer’s instructions rather than assuming every instrument uses the same schedule.
If an EBT fails an external calibration check, remove it from service. It cannot return to DOT testing until it is calibrated by a certified calibration technician and passes another external calibration check.
A failed check can affect earlier results: every result of 0.02 or higher since the last valid external calibration check must be cancelled. For this reason, it is highly recommended to run an external calibration check after every confirmation test of 0.02 or higher.
Maintain organized equipment records so the affected testing period can be identified quickly. An accuracy check verifies performance; a calibration adjustment changes the instrument’s response. Technicians need to understand both functions and their authorization to perform them.
Read our article, “Breathalyzer Calibration Matters: Tips for Ensuring Accuracy” for precision requirements and steps.
Correctable Flaws That Can Still Cancel an Alcohol Test
Under Part 40 §40.269, three problems require cancellation unless corrected:
- The BAT or screening test technician (STT) did not sign the ATF.
- The technician did not document that the employee failed to sign Step 4 after the positive confirmation result was obtained.
- A non-DOT form was used for a DOT alcohol test.
These are correctable flaws. They require action, but discovering one does not automatically mean the result is lost.
Mistake 6: Leaving Required Documentation Unresolved
When the BAT is made aware of a correctable flaw, they must provide documentation to the individual(s) that notified the BAT of the correctable flaw. Doing so corrects the mistake and keeps the test valid. The BAT must provide it in writing with a signed statement confirming its accuracy.
Using a non-DOT form requires additional documentation: certification that it contains the information needed for a valid DOT alcohol test, an explanation of its inadvertent use or circumstances beyond the technician’s control, and preventive steps. DOT requires this information on the same business day the problem is reported, transmitted by fax or courier.
If the flaw cannot be corrected, cancel the test.
Build a final paperwork review into your routine. Treat the ATF as part of the testing procedure rather than a task to finish between appointments.
Mistake 7: Confusing an Employee’s Missing Signature With Refusal
For confirmation results of 0.02 or higher, direct the employee to sign and date Step 4 of the ATF. If the employee does not sign, document that fact in Remarks. This does not constitute a refusal to test.
The correctable flaw is the technician’s missing notation, not the employee’s missing Step 4 signature. Train staff to identify the specific ATF step involved before reporting a refusal or recommending cancellation.
Other DOT Alcohol Testing Mistakes BATs Must Recognize
Not every deviation is a fatal flaw. BATs need to recognize errors that require documentation, referral, or another prescribed response.
Starting Confirmation More Than 30 Minutes After Screening
DOT says confirmation should begin as soon as possible after the minimum wait and within 30 minutes of screening completion. However, exceeding 30 minutes does not automatically invalidate either test.
Proceed with confirmation, document the elapsed time and reason for delay, and do not restart screening to reset the clock. The delay may still constitute a regulatory violation.
Mishandling a Transfer to Another Testing Site
When confirmation requires another location, the screening technician must provide and document waiting-period instructions, arrange the required observation during transport, and ensure the accompanying person carries the ATF copy. Direct the employee not to drive.
Transit can count toward the waiting period when the required instructions were provided. The receiving BAT must verify their documentation; otherwise, carry out the waiting-period requirement. A BAT who did not conduct screening must use a new ATF and document that a different technician performed screening.
A documented handoff helps the receiving technician establish what occurred before arrival.
Cancelling a Test Because of Insufficient Breath
An employee’s inability to provide sufficient breath requires the §40.265 process. Give the required instructions and opportunities, document unsuccessful attempts, and notify the DER.
When a medical evaluation is required, the employer directs it. The physician’s determination can lead to cancellation or a refusal outcome. A BAT should not assume that an unsuccessful breath sample establishes either result.
Saliva and Breath Tube Screening Have Their Own Fatal Flaws
BATs who also perform screening with saliva screening devices must recognize device-specific cancellation risks.
These include reading the test strip result outside the required time window, using an expired testing device, and saliva-device activation failures.
Follow the applicable manufacturer’s instructions and DOT procedures for the device in use. Saliva screening results must not be read before the manufacturer’s specified time and must be read within 15 minutes of the test. If a saliva device fails to activate, follow §40.245’s replacement-testing procedure.
What Should a BAT Do When a Test Must Be Cancelled?
Where practicable, inform the employee, document the problem, and promptly repeat the testing process. Under the Part 40 §40.271 general repeat-testing procedure, use a new ATF and sequential test number, with replacement equipment when needed.
Notify the affected DER within 48 hours of cancellation. A cancelled test is neither positive nor negative and does not count toward minimum random testing requirements. Employers cannot automatically order another test solely because cancellation occurred; Part 40 specifies the permitted circumstances. Cancellation itself also does not establish grounds for a non-DOT test.
Prevent Repeat Mistakes With BAT Training
If your mistake causes cancellation through a fatal or uncorrected flaw, error correction training must be administered within 30 days of notification. It must address the problem area that caused the cancellation and include three consecutive error-free mock tests: one uneventful scenario and two related to the error.
This differs from initial qualification and refresher training, which require seven consecutive error-free BAT mock tests. Refresher training is required at least every five years.
AlcoPro offers online BAT training that combines DOT procedures with instrument-specific instruction and mock testing. For a complete guide to BAT certification, read our article, “What is a Breath Alcohol Technician? A Complete Certification Guide”.
Explore AlcoPro’s DOT training courses to prepare for initial qualification or your next refresher.
Frequently Asked Questions
Does every mistake on an ATF cancel the test?
No. Minor administrative errors, such as omitting a middle initial, do not justify cancellation when they do not significantly affect the employee’s right to a fair and accurate test. Document errors even when they do not require cancellation.
Can a signed statement fix a fatal flaw?
No. A signed statement or Memorandum for Record (MFR) can address correctable flaws. It cannot validate a result affected by a fatal flaw. Follow the applicable repeat-testing procedures instead.
Does error correction training replace five-year refresher training?
No. Error correction training targets the error that caused cancellation. Refresher training covers the qualification and proficiency requirements on the five-year schedule. Track both obligations separately.